Warmlyyours Snow Melting & Slab Heating User Manual

Installation Manual for Snow Melting24/7 Installation Support • Lifetime Technical Assistance • Free Design Service • www.WarmlyYours.com • (8

92’ (61cm)or3’ (91cm)Length 5’ (152cm) min 50’ (1524cm) max20’ (610cm) Cold LeadOuter Sheath PVC/PololefinPolyester SheathMetal Sheath (Copper/Galvani

106.0 TESTING THE MATS AND CABLE6.1 TEST ONE: INSULATION RESISTANCE (MEGOHMMETER REQUIRED)1. Connect one meter clamp to the cold lead (pigtail) inn

8.0 APPENDIX A:WARMLYYOURS SNOW MELTING MATS (SUITABLE FOR ASPHALT, CEMENT AND UNDER PAVERS)Part # Size (ft/m) Voltage Area (ft2/m2) Cable Length (ft/

APPENDIX B:WARMLYYOURS SNOW MELTING CABLES (ALL-PURPOSE FOR ASPHALT, CEMENT AND UNDER PAVERS)Part # Voltage Cable Length Total Ohms Total Watts Watts/

132” to 3”(51mm to 76mm) of finished asphalt.1.5” to 2” (38mm to 51mm) of base/primer asphalt4” to 8” (102mm to 203mm) of crushed aggregateWire mesh a

2” to 3”(51mm to 76mm) of finished asphalt.1.5” to 2” (38mm to 51mm) of base/primer asphalt4” to 8” (102mm to 203mm) of crushed aggregateWire mesh abo

APPENDIX E:CROSS-SECTION OF SNOW MELTING CABLE IN MORTAR BED UNDER PAVERS152” to 3”(51mm to 76mm) of finished asphalt.1.5” to 2” (38mm to 51mm) of bas

APPENDIX F:CROSS-SECTION OF INDOOR SLAB HEATING CABLE IN CONCRETE162” to 3”(51mm to 76mm) of finished asphalt.1.5” to 2” (38mm to 51mm) of base/primer

17APPENDIX G:SNOW MELT DIAGRAM 240V - TYPICAL LINE DIAGRAM (FOR 6 CIRCUITS/CABLES) WITH PREMIUM CONTROL240V CIRCUITSAIR-SSLOW VOLTAGE (24V)LOW VOLTAGE

APPENDIX H:SNOW MELT DIAGRAM 240V - TYPICAL LINE DIAGRAM (FOR 6 CIRCUITS/CABLES) WITH ECONOMY CONTROL240V CIRCUITSSLAB-SSLOW VOLTAGE (24V)120V CONTROL

CONTENTS1.0 Product Specications ... 12.0 Selection of the Heating Syst

19APPENDIX I:SNOW MELT DIAGRAM 240V - TYPICAL LINE DIAGRAM (FOR 6 CIRCUITS/CABLES) WITH MANUAL CONTROL240V CIRCUITS120V CONTROLPOWERHeater cable pigta

APPENDIX J:SNOW MELTING DIAGRAM: 240V - TYPICAL LINE DIAGRAM (FOR 6 CIRCUITS/CABLES) WITH VALUE CONTROL240V CIRCUITS120V CONTROLPOWERHeater cable pigt

Installation Support • No Nonsense™ Warranty •(800) 875-5285 • www.WarmlyYours.comAPPENDIX K:SLAB HEATING DIAGRAM: 240V - TYPICAL LINE DIAGRAM (FOR

Installation Support • No Nonsense™ Warranty •(800) 875-5285 • www.WarmlyYours.comWarmlyYours Snow Melting and Slab Heating WarrantyWarmlyYours, In

Installation Support • No Nonsense™ Warranty •(800) 875-5285 • www.WarmlyYours.comInstall Date:Installed Under: q Concrete q Asphalt q Pavers q

2.0 SELECTION OF THE HEATING SYSTEMSelection of your Heating System will depend on the application. The following can be taken as a general guide:INST

4.0 INSTALLATION FOR INDOOR & OUTDOOR SLAB HEATING4.1 TEMPERATURE CONTROLLER & SENSORWe recommend a standard Programmable Thermostat with a

4.3 PRE-INSTALLATION PREPARATIONS1. Review the custom installation plan for the area requiring the Heating System and verify dimensions li

54.5 OPERATING TIPS1. Energy consumption will vary depending on ambient temperature and building insulation. For lower energy consumption, u

65.3 INSTALLATION UNDER ASPHALT1. Ensure that paving contractor has a solid base of 4” to 8” (102 mm to 203 mm) of crushed rock aggregate tamped do

75.4 INSTALLATION UNDER CONCRETE1. Ensure that the concrete contractor has installed a solid base of 4” to 8” (102 mm to 203mm) of crushed rock aggr

85.5 INSTALLATION UNDER PAVERS (STONE OR BRICK)1. Ensure that there is a solid base of 4” to 8” (102mm to 203mm) of crushed rock aggregate base and t